P4C198L-25PMB中文资料(2)

P4C198/198L, P4C198A/198AL

MAXIMUM RATINGS(1)

VCC

Power Supply Pin withRespect to GNDTerminal Voltage withRespect to GND(up to 7.0V)

Operating Temperature

–0.5 to +7–0.5 toVCC +0.5–55 to +125

V

SymbolTBIASTSTG

V°C

PTIOUT

ParameterTemperature UnderBias

Storage TemperaturePower DissipationDC Output Current

Value–55 to +125–65 to +150

1.050

Unit°C°CWmA

VTERMTA

RECOMMENDED OPERATING

TEMPERATURE AND SUPPLY VOLTAGE

Grade(2)Military

AmbientTemperature

GND0V0V0V

VCC5.0V ± 10%5.0V ± 10%5.0V ± 10%

CAPACITANCES(4)

VCC = 5.0V, TA = 25°C, f = 1.0MHzSymbolCINCOUT

ParameterInput CapacitanceOutput Capacitance

ConditionsTyp.UnitVIN = 0VVOUT = 0V

57

pFpF

–55°C to +125°C0°C to +70°CCommercial

–40°C to +85°CIndustrial

DC ELECTRICAL CHARACTERISTICS

Over recommended operating temperature and supply voltage(2)SymbolVIHVILVHCVLCVCDVOLVOHILIILO ISB

Parameter

Input High VoltageInput Low VoltageCMOS Input High VoltageCMOS Input Low VoltageInput Clamp Diode VoltageOutput Low Voltage(TTL Load)

Output High Voltage(TTL Load)

Input Leakage CurrentOutput Leakage Current

VCC = Min., IIN = –18 mAIOL = +10 mA, VCC = Min.IOL = +8 mA, VCC = Min.IOH = –4 mA, VCC = Min.VCC = Max. Mil.VIN = GND to VCC Ind./Com’l.VCC = Max., CE = VIH, Mil.VOUT = GND to VCC Ind./Com’l.

Test Conditions

P4C198 / 198AP4C198L / 198AL

Unit

MinMaxMinMax2.2VCC +0.52.2VCC +0.5V–0.5(3)–0.5(3)0.5

0.4

2.4–10–5–10–5______

+10+5+10+540352015

2.4–5n/a–5n/a______

+5n/a+5n/a40n/a1.5n/a

0.80.2–1.2

0.5

0.4

–0.5(3)–0.5(3)

0.80.2–1.2

VVVVVVVµAµAmA

VCC –0.2VCC +0.5VCC –0.2VCC +0.5

CE1, CE2 ≥ VIH Mil.

Standby Power Supply

VCC = Max ., Ind./Com’l.

Current (TTL Input Levels)

f = Max., Outputs OpenStandby Power SupplyCurrent

(CMOS Input Levels)

CE1, CE2 ≥ VIH Mil.VCC = Max., Ind./Com’l.f = 0, Outputs OpenVIN ≤ VLC or VIN ≥ VHC

mA

ISB1

n/a = Not Applicable

Notes:

1.Stresses greater than those listed under MAXIMUM RATINGS maycause permanent damage to the device. This is a stress rating onlyand functional operation of the device at these or any other conditionsabove those indicated in the operational sections of this specificationis not implied. Exposure to MAXIMUM ratingconditions for extendedperiods may affect reliability.

2.Extended temperature operation guaranteed with 400 linear feet perminute of air flow.

3.Transient inputs with VIL and IIL not more negative than –3.0V and–100mA, respectively, are permissible for pulse widths up to 20 ns.4.This parameter is sampled and not 100% tested.

Document # SRAM113 REV APage 2 of 13